Very disappointed with this skid plate. For the instillation they want you to drill close to 40 holes into your frame with self tapping screws. The biggest slap in the face is that there’s more than enough factory threaded holes they could have utilized for the installation. I would not buy this again. For the price they want for this skid plate they should have put more thought into the design so that it made use of the threaded holes that are already there. There’s other skid plates on the market that do just that. Buy one of those instead. The Super ATV is a $1000 piece of plastic tat will require you to drill 40 holes into your frame that will eventually start to rust and compromise the integrity of the frame in your very expensive side by side.
And before someone responds to this review saying that I got the wrong skid plate. I’m well aware there’s 2 versions. 16-21 and 22+. I’m 1000% sure that I got the right one for my SXS.

The product itself seems very durable, need time to rate after use. But it shipped with no instructions, missig 2-6mm x 40mm self drilling bolts, 4- 8mm x 30mm bolts, and 2 of the recessed pockets were incomplete on each end of one plate.

The product is supper strong, materials and instructions were 8/10. Some of the self tappers couldn’t go through the steel frame as it was to think. Ended up more drilling all the holes, that worked real good. The only issue with the supplied materials was the bar that strengthens the back plate to the side plate. It wouldn’t fit any holes as pre drilled, had to shorten and make new attachment holes. Other than that it was good to go. I did not tip it over as the instructions suggested, ran it up on two sets of ramps front and back.

Good fit for my 2023 ZForce 950 Ho Ex

Fast shipping

Well fit Easy to di from under unit juts put it up on 4 vehicle ramps. Well fit.

Good communication fast delivery

fit well went on easy

Strong and sturdy. Installation was ok- I had an extra metal 1/8” tranny skid plate and this went on top without issues. Good peace of mind

All components fit like they should. Only took a couple hours to install after removing the stock skid plates and a couple broken bolts. The product seems to be made with the highest quality and is heads above the stock skid plates. I’m looking forward to seeing how it performs on the trails. My only complaint is that there isn’t a pre-made access for draining engine oil, but I’ll make my own when it is time for oil change. Do yourself a favour and put the machine on its side to install. This made it very easy. Remember to drain your engine oil before laying machine on its side.

Great quality. Very thick. Fit together good and tons of hardware mounting it on. The stock z950 skid plate is horrible this is a huge improvement

Installation is made simple once the machine is positioned on its side. The skid plate offers a significant upgrade from the OEM's 1/8" thickness. I have a complaint regarding my purchase. It appears that the item I received had been returned previously and they had kept the Super Atv decals! Is a purchase really complete without some awesome decals?

Fits really well and better then the one that comes with the machine

Exellent design, easy to install if ypu take your time.

Over all very good service from Revco - I'm happy with the finished product but this is no "easy" install. It's tedious, precise and there is drilling. As the instructions say, if you can tip your bike on its side, or climb a tree, do it. I did mine from undereath while sliding around the garage floor and ate some dirt and a few drill shavings. I think i was short a few screws too but nothing i couldn't get at the local hardware store. This fit both a RZR XP 4 1000 and RZR XP 4 1000 High Lifter edition. Take your time, keep everything slightly loose for play/wiggle room and then button it all up at the end it will work flawless. Extra thought process required if you have a bumper already installed but easy enough to figure out.

What's interesting is that the Super ATV site says this model fits the XP 4 1000 but not the high lifter edition, they're installed exactly the same underneath so not sure why it says that. Careful of the gas tank when putting in screws on the left side too.

Skid plate is nice and heavy, looks like it will take quite a beating. Installation was pretty straight forward as long as you start with the middle piece as it is the only piece that has a fixed stating point where it fits under the flange in the frame . The hardware supplied was great , just be prepared to drill just about every hole as not very many line up with the stock holes. I haven’t been out for a ride yet to give it the ultimate test but things look pretty good under my Maverick Trail compared to what comes stock

This plate fits well and should provide great protection as compared to stock! Some drilling is required to install but no big deal !

Delivery was very fast. Installation of this was straight forward and it looks as if it's going to provide major protection for passengers and driveline components. Very happy with this purchase.

Thing is super thick, have to drill new holes when mounting it but parts provided works out good! Would say go for it if your on the fence won’t be disappointed!

A little bit of drilling to get it on but fits great.

This is definitely worth the cost, it is sooooooo much heavier than the one that comes on the bike!!!! you may get a bit sore in the muscles, getting it on as it's pretty solid. I will no longer worry about each rock or bump we hit though! Well worth the costs and great addition to any 4 wheeler/side by side!!

Great product, easy to install

Ordered this for my 2021 General XP 1000 only to find out I had to cut 3 inches off the front of the skid plate to prevent it from rubbing on my tires. The product is tough but doesn't line up together very well and the self tapping screws are breaking off after the first ride. Not to impressed with this product. It is better than stock but has its setbacks.

In general the installation went well after removing the factory plate. There was one factory drilled hole in the rear left hand plate that did not line up with frame, it was out by an inch or more. Two later Han supplied screws were needed to install the small front plate as the predrilled holes were larger.

Over all the fit is good and definitely better protects the underside of machine

Nice think plate. It should be 8 inches longer in the rear to cover the rear differential

I bought this after a piece of 2 foot rebar punctured the floor and hit the edge of my boot. It could have been much worse, just missing my foot and leg. Install was more time consuming than I thought it would be, but still straight forward and and easy DIY project. The added weight didn't noticeably affect performance and actually lessened the squeaks and rattles from my machine.

Take your time on install. It does fit very well. Been bullet proof so far in our rocky tight trails on Vancouver island